Apache Cassandra is a distributed NoSQL database management system designed to handle large amounts of data across nodes, providing high availability with no single point of failure. It uses asynchronous masterless replication allowing low latency operations for all clients. Cassandra is deployed usually as a
statefulset on Kubernetes and requires persistent storage for each instance of Cassandra. OpenEBS provides persistent volumes on the fly when Cassandra instances are scaled up.
Advantages of using OpenEBS for Cassandra database:
- No need to manage the local disks, they are managed by OpenEBS
- Large size PVs can be provisioned by OpenEBS and Cassandra
- Start with small storage and add disks as needed on the fly. Sometimes Cassandra instances are scaled up because of capacity on the nodes. With OpenEBS persistent volumes, capacity can be thin provisioned and disks can be added to OpenEBS on the fly without disruption of service
- Cassandra sometimes need highly available storage, in such cases OpenEBS volumes can be configured with 3 replicas.
- If required, take backup of the Cassandra data periodically and back them up to S3 or any object storage so that restoration of the same data is possible to the same or any other Kubernetes cluster
Note: Cassandra can be deployed both as
deployment or as
statefulset. When Cassandra deployed as
statefulset, you don't need to replicate the data again at OpenEBS level. When Cassandra is deployed as
deployment, consider 3 OpenEBS replicas, choose the StorageClass accordingly.
As shown above, OpenEBS volumes need to be configured with three replicas for high availability. This configuration work fine when the nodes (hence the cStor pool) is deployed across Kubernetes zones.
If OpenEBS is not installed in your K8s cluster, this can done from here. If OpenEBS is already installed, go to the next step.
Connect to MayaOnline (Optional) : Connecting the Kubernetes cluster to MayaOnline provides good visibility of storage resources. MayaOnline has various support options for enterprise customers.
Configure cStor Pool
After OpenEBS installation, cStor pool has to be configured.If cStor Pool is not configure in your OpenEBS cluster, this can be done from here. During cStor Pool creation, make sure that the maxPools parameter is set to >=3. Sample YAML named openebs-config.yaml for configuring cStor Pool is provided in the Configuration details below. . If cStor pool is already configured, go to the next step.
Create Storage Class
You must configure a StorageClass to provision cStor volume on given cStor pool. StorageClass is the interface through which most of the OpenEBS storage policies are defined. In this solution we are using a StorageClass to consume the cStor Pool which is created using external disks attached on the Nodes. Since Cassandra is a StaefulSet application, it requires only one replication at the storage level. So cStor volume
replicaCountis 1. Sample YAML named openebs-sc-disk.yamlto consume cStor pool with cStorVolume Replica count as 1 is provided in the configuration details below.
Launch and test Cassandra
Create a sample
cassandra-statefulset.yamlfile in the Configuration details section. This can be applied to deploy Cassandra database with OpenEBS. Run
kubectl apply -f cassandra-statefulset.yamlto see Cassandra running. This will configure required PVC also.
In other way , you can use Cassandra image with helm to deploy Cassandra in your cluster using the following command.
helm install --namespace "cassandra" -n "cassandra" --storage-class=openebs-cstor-disk incubator/cassandra
Post deployment Operations
Monitor OpenEBS Volume size
It is not seamless to increase the cStor volume size (refer to the roadmap item). Hence, it is recommended that sufficient size is allocated during the initial configuration. However, an alert can be setup for volume size threshold using MayaOnline.
Monitor cStor Pool size
As in most cases, cStor pool may not be dedicated to just Cassandra database alone. It is recommended to watch the pool capacity and add more disks to the pool before it hits 80% threshold. See cStorPool metrics
#Use the following YAMLs to create a cStor Storage Pool. # and associated storage class. apiVersion: openebs.io/v1alpha1 kind: StoragePoolClaim metadata: name: cstor-disk spec: name: cstor-disk type: disk poolSpec: poolType: striped # NOTE - Appropriate disks need to be fetched using `kubectl get disks` # # `Disk` is a custom resource supported by OpenEBS with `node-disk-manager` # as the disk operator # Replace the following with actual disk CRs from your cluster `kubectl get disks` # Uncomment the below lines after updating the actual disk names. disks: diskList: # Replace the following with actual disk CRs from your cluster from `kubectl get disks` # - disk-184d99015253054c48c4aa3f17d137b1 # - disk-2f6bced7ba9b2be230ca5138fd0b07f1 # - disk-806d3e77dd2e38f188fdaf9c46020bdc # - disk-8b6fb58d0c4e0ff3ed74a5183556424d # - disk-bad1863742ce905e67978d082a721d61 # - disk-d172a48ad8b0fb536b9984609b7ee653
apiVersion: storage.k8s.io/v1 kind: StorageClass metadata: name: openebs-cstor-disk annotations: openebs.io/cas-type: cstor cas.openebs.io/config: | - name: StoragePoolClaim value: "cstor-disk" - name: ReplicaCount value: "1" provisioner: openebs.io/provisioner-iscsi reclaimPolicy: Delete
apiVersion: apps/v1beta1 kind: StatefulSet metadata: name: cassandra labels: app: cassandra spec: serviceName: cassandra replicas: 3 selector: matchLabels: app: cassandra template: metadata: labels: app: cassandra spec: containers: - name: cassandra image: gcr.io/google-samples/cassandra:v11 imagePullPolicy: Always ports: - containerPort: 7000 name: intra-node - containerPort: 7001 name: tls-intra-node - containerPort: 7199 name: jmx - containerPort: 9042 name: cql resources: limits: cpu: "500m" memory: 1Gi requests: cpu: "500m" memory: 1Gi securityContext: capabilities: add: - IPC_LOCK lifecycle: preStop: exec: command: ["/bin/sh", "-c", "PID=$(pidof java) && kill $PID && while ps -p $PID > /dev/null; do sleep 1; done"] env: - name: MAX_HEAP_SIZE value: 512M - name: HEAP_NEWSIZE value: 100M - name: CASSANDRA_SEEDS value: "cassandra-0.cassandra.default.svc.cluster.local" - name: CASSANDRA_CLUSTER_NAME value: "K8Demo" - name: CASSANDRA_DC value: "DC1-K8Demo" - name: CASSANDRA_RACK value: "Rack1-K8Demo" - name: CASSANDRA_AUTO_BOOTSTRAP value: "false" - name: POD_IP valueFrom: fieldRef: fieldPath: status.podIP readinessProbe: exec: command: - /bin/bash - -c - /ready-probe.sh initialDelaySeconds: 15 timeoutSeconds: 5 # These volume mounts are persistent. They are like inline claims, # but not exactly because the names need to match exactly one of # the stateful pod volumes. volumeMounts: - name: cassandra-data mountPath: /cassandra_data volumeClaimTemplates: - metadata: name: cassandra-data annotations: volume.beta.kubernetes.io/storage-class: openebs-cstor-disk spec: accessModes: [ "ReadWriteOnce" ] resources: requests: storage: 5G